Product Description
Screw juicing machine
Spiral juicer also known as fruit and vegetable slag juice machine, fruit and vegetable slag juice machine, spiral fruit and vegetable
slag juice machine, fruit and vegetable juicer, fruit and vegetable beater, crusher feed must be uniform, strictly prohibit hard foreign
matter into the hopper, so as not to damage the screen.Screw juicer is developed by absorbing international advanced technology.
The machine is widely used, can press watermelon, grape, strawberry, pear, apple, lemon, orange, orange, tomato, papaya, radish,
ginger and other fruit and vegetable juice. The main component of the equipment is that the bottom diameter of the screw gradually
increases along the direction of the slag outlet and the pitch gradually decreases. When the material is pushed by the screw, the
press of the material is formed due to the reduction of the volume of the spiral cavity.
Working principle
The main component of this equipment is the installation of a crushing device on the feeding hopper. There are three sets of flying
knives and one set of bottom knives on the rotor. The flying knives rotate around their own axis in a fixed gap between the bottom
knives, so that fruits and vegetables can reach a particle size of 2-5 millimeters and be crushed, directly entering the spiral juice
extraction system to improve the juice extraction effect. The main component of spiral juice extraction is the spiral, which gradually
increases the bottom diameter and decreases the pitch along the direction of the slag outlet. When the material is pushed forward
by the spiral, the volume of the spiral cavity shrinks, forming pressure on the material. The rotation direction of the spiral spindle is
clockwise when viewed from the feeding hopper towards the slag groove.
The raw materials are added to the feeding hopper and compressed under the push of the screw. The squeezed juice flows into the
bottom juicer through the filter screen, while the waste is discharged through the annular gap formed between the screw and the
pressure regulating conical part. The size of the gap can be adjusted by the axial movement of the pressure regulating head. Used
clockwise (when rotating the handwheel bearing seat from the slag discharge groove of the equipment to the feeding hopper end,
the pressure regulating head will turn to the left, and the gap will decrease; otherwise, the gap will increase). Changing the size of
the gap, that is, adjusting the resistance of the slag discharge, can change the slag discharge rate. However, if the gap is too small,
under strong compression, some of the slag particles will be squeezed out together with the juice through the filter screen. Although
the juice output increases, the quality of the juice relatively decreases, The size of the gap should depend on the specific process
requirements of the user.
Product Parameters
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1080*480*1190
|
|
|
|
|
|
|
|
1400*550*1700
|
Performance characteristics:
1, advanced design, compact structure, beautiful and generous.
2, the machine is composed of crusher and screw juicer two parts of the combination, automatic crushing, juicing, slag discharge process.
3, the use of conical screw, large capacity, high juice yield.
4, high efficiency and energy saving, low noise, no pollution.
5.All parts in contact with the material are made of stainless steel;
Installation, operation and maintenance:
1. The machine must be installed horizontally and fixed with anchor screws.
2. Operation:When the equipment is started, the indenter should be adjusted to make the annular gap large, and then the gap gradually
decreases. After meeting the process requirements, the handwheel bearing seat position is fixed with the brake.
3, the feed must be uniform, strictly prohibit hard foreign matter into the hopper, so as not to damage the screen.
4. Maintenance: Wash the filter with water and brush after each shift. If the juice with more fine fiber is filtered, it is necessary to add a
washing net depending on the production situation, and clean all the machines with hot water after the press is finished.
5.The bearings are regularly replaced with clean lubricating grease, and the normal operating temperature of the bearings is less than
75 degrees.
Company Profile
Antler Automation Equipment (Suzhou) Co., Ltd.is one of the most experienced manufacturer for dairy, fruits & vegetables,
and beverages processing equipment in food industry.We are capable of design and produce turnkey project for UHT /pasteurized
milk & yogurt, concentrated and powder milk, fruit juice & concentrate ,bottled water and beverages etc.
We focus on innovative food and beverage process technology and mechanical manufacture technology, from standard plant
systems to customized solutions, designed to meet optimum hygiene and quality standards, while operating efficiently and sustainably.
As a true producer and partner of clients and relations who are professionally involved in food and beverages project and who rely
on continuous precision and high services for project design, equipment manufacturing and commissioning, and also staff training .
Our technical expertise is complemented by project management, planning and cost control services to help our customers achieve
flexible and cost-effective food production.
Certifications
Packaging & Shipping
FAQ
1. Are you a manufacturer or a trading company?
We are a professional manufacturer of food & beverages processing machine.
2. What's the price of your machines?
Please contact us for further communication, we shall make you an offer.
3. What is the payment terms?
T/T or L/C; by T/T 30% as down payment, 70% by T/T before delivery, 100L/C at sight before shipment.
4. What is the supply scope?
We can provide you with turnkey project for complete dairy,fruit and vegetables processing machine.
Along with project design and basic formula.
5. What is the workshop size required?
The production line can be put in straight line and also can change the direction according to your
factory size. We can design the layout according to your factory size.
6. What's your Warranty time?
Our warranty is 2 years after delivery.
Audited Supplier 
){kind=link}
){kind=link}